Wearables Accessories

SF-DEV-13814

This is 12 meters of smooth conductive thread spun from stainless steel fiber and wound on a plastic bobbin. Use it to sew up all of your e-textile projects. This small bobbin is a great way to get into wearable electronics without the upfront cost of buying an entire spool of...

LB-LR0295

These are a simple 9v battery holder with DC connector.

LB-LR0309-16

Flat 4xAA battery holder with a barrel jack.

KI-2762

Add an individually addressable full colour LED to your E-Textiles projects with the Kitronik Sewable ZIP LED. This new addition to our Electro Fashion range incorporates a full colour addressable ZIP LED, which can be controlled by a suitable processor such as the micro:bit.

AF-653

This battery holder is by far the easiest way to add a battery to a small wearable project. By coincidence, there are two small 1mm diameter holes in the metal connection tabs, just large enough for a #5 or smaller needle to pass through. One tab connects to common ground (neg...

AF-1871

Simple but effective - this sewable breakout board has a CR2032 coin cell battery holder soldered on, an on/off switch and 0.1" pitch breakout pins for easy connecting. Great for powering very low-current projects, or adding a battery backup circuit to a real-time-clock or sim...

LB-LR0294

 

LB-LR0309-20

Single Slots 1x 9V Battery Holder Case with wire leads for soldering / connecting.

AF-783

This tiny coin cell battery holder is ideal for small portable or wearable projects.

$2.85
SF-TOL-10405

This set of sewing needles is a must-have when stitching together your next e-textile project. Each envelope contains three 48mm, 1.23mm thick needles and two smaller 39mm, 0.67mm thick needles. The eye of each size needle is large enough to easily thread with our conductive t...

AF-1008

Connect this to that without soldering using these handy mini alligator clip test leads. 15" cables with alligator clip on each end, colour coded. You get 12 pieces in 6 colours. Strong and grippy, these always come in handy! We often use these in conjunction with a multimeter...

AF-615

Mighty needles, sew like the wind! This needle set is the only one you'll need for any sort of hand sewing, especially using our conductive thread and wearable electronics parts.

LB-LR0309-18

This is an incredibly simple one cell 18650 Battery Holder. When someone thinks of 18650 Cells they tend to think of flashlights first, which is fair since that is what they have been primarily used for.

SF-DEV-11791

This is about 360 yards of conductive thread spun from stainless steel fiber and wound on a spool. You can use it as a creative way to connect various electronics onto clothing projects. This large spool is a great way to get into wearable electronics without a large upfront c...

AF-727

This battery holder connects 3 AAA batteries together in series for powering all kinds of projects. We spec'd these out because the box is slim, and 3 AAA's add up to about 3.3-4.5V, a very similar range to Lithium Ion/polymer (Li-Ion) batteries and have an on-off switch. That...

AF-1170

These magnetic pin backs have two pieces: a metal bar with adhesive strip and a plastic piece with two strong rare-earth magnets.

SF-COM-11288

These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot. Simply apply 5VDC to the wire leads and within minutes, the pad will begin to warm up.

TB-PH9209

The holders are moulded in Delryn with corrosive resistant nickel plated springs and studs.- All have connection wires 150mm long- We can supply OEM quantities of holders with special configurations.

SF-DEV-10172

Here we have some conductive ribbon. Essentially, it’s a fabric with 3 conductors woven into the ribbon. It measures roughly 0.2" wide and 0.03" thick. You will get a 1 yard (~3 foot long) section of ribbon. It has very little (negligible) resistance to it. The material is 68%...

TB-PH9200

The holders are moulded in Delryn with corrosive resistant nickel plated springs and studs.

TB-PH9202

The holders are moulded in Delryn with corrosive resistant nickel plated springs and studs.- All have connection wires 150mm long- We can supply OEM quantities of holders with special configurations.

TB-PH9206

The holders are moulded in Delryn with corrosive resistant nickel plated springs and studs.- All have connection wires 150mm long- We can supply OEM quantities of holders with special configurations.

TB-PH9210

* 150mm long tinned leads

TB-PH9235

- Plastic holder for 9V 216 batteries

TB-PH9203

The holders are moulded in Delryn with corrosive resistant nickel plated springs and studs.- All have connection wires 150mm long- We can supply OEM quantities of holders with special configurations.

AF-1577

We've got some awesome LED goggle tutorials, and now you want to make your own, right? So pick up a pair of NeoPixel rings and these costuming goggles and get to it!

SF-COM-14112

This EeonTex fabric is a bidirectionally stretchy nylon/spandex, elastic fabric coated with a long-lasting conductive formulation. This material has found use in soft, biometric strain and pressure sensors, such as for beds and seats, or where conforming to irregular shapes is...

IT-IM120803026

Overview

SF-DEV-10056

This is a conductive knit fabric for use in e-textiles. It is similar in feel to a nylon ripstop material. It is highly conductive with a surface resistivity of < 0.02 ohm/sq. This is a great add-on to any LilyPad project.

AF-700

This skill badge is self-fulfilling! Normally you would get the badge after the project is done, but in this case, the badge can be part of the project! The solar panel is epoxied into a round disc 55mm diameter (about 2.2 inches), its rugged and looks cool besides. We include...