Sensors

LB-LR0044

The MPU-6050 sensor contains a MEMS accelerometer and a MEMS gyro in a single chip. It is very accurate, since it contains 16-bits analog to digital conversion hardware for each channel. Therefor it captures the x, y, and z channel at the same time.

DF-DFR0024

While there are many types of temperature sensors available in the market, the DS18B20 arduino Temperature Sensor form DALLAS is the best choice in applications which require high accuracy and high reliability. Its ultra-small size, low hardware overhead, strong anti-interfere...

AF-165

Wide range, low power temperature sensor outputs an analog voltage that is proportional to the ambient temperature. To use, connect pin 1 (left) to power (between 2.7 and 5.5V), pin 3 (right) to ground, and pin 2 to analog in on your microcontroller. The voltage out is 0V at -...

SF-SEN-12064

The HTU21D is a low-cost, easy to use, highly accurate, digital humidity and temperature sensor.

AF-828

Measure liquid/water flow for your solar, computer cooling, or gardening project using this handy basic flow meter.

FT-HUMID

Measure temperature and relative humidity using a simple interface that requires just three wires to the sensor: GND, power, and data. Supported by an Arduino library that makes it very easy to read values into your project, so with a single I/O line from your microcontroller ...

LB-LR0298

This stand alone DHT11 can read the temperature and humidity and send the information over a one wire, simplex serial bus. Arduino.cc provides a DHT11 library to aid in communicating with this module.

SF-SEN-00250

10K thermistor with a negative temperature coefficient. Good choice for temp-sensing applications when you need a reliable NTC thermistor.

SF-SEN-11050

This sealed digital temperature probe lets you precisely measure temperatures in wet environments with a simple 1-Wire interface. The DS18B20 provides 9 to 12-bit (configurable) temperature readings over a 1-Wire interface, so that only one wire (and ground) needs to be connec...

PL-1185

Overview

DF-SEN0114

A soil moisture sensor can read the amount of moisture present in the soil surrounding it. It's an ideal for monitoring an urban garden, or your pet plant's water level. This is a must have component for a IOT garden / Agriculture!

DF-FIT0503

INTRODUCTION

SF-COM-09312

The US1881 is an integrated Hall effect latched sensor. That’s nice but what does it do? Holding a magnet near the sensor will cause the output pin to toggle. This makes for a robust presence sensor. A reed sensor also works nicely, but can be limited by the glass encapsulatio...

DF-DFR0063

This is an 16x2 LCD display screen with with I2C interface. It is able to display 16x2 characters on 2 lines, white characters on blue background.

LB-LR0043

The Water Sensor is a small analogue sensor which can detect the amount of water there is on itself. The value will increase as the more water is put onto it. This can be used as a simple water level meter. All that you need to do to connect this sensor to your project is thre...

DF-SER0011

This is a metal gear servo(2.5kg) from Goteck.It's very small, lightweight, and powerful! Metal gear for longer wear life and extra strength in demanding applications. Perfect for use in medium-sized electric airplanes,helicopters or mini Robots.

SF-SEN-08880

This alcohol sensor is suitable for detecting alcohol concentration on your breath, just like your common breathalyzer. It has a high sensitivity and fast response time. Sensor provides an analog resistive output based on alcohol concentration. The drive circuit is very simple...

LB-LR0400

Description: This straight bar load cell (sometimes called a strain gauge) can translate up to 1kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pres...

DF-DFR0032

Here is the simplest sound making module that you can use High/Low to drive it. Just change the frequency it buzz, you can hear different sound. It is widely used on your daily application, like PC, refrigerator,phones and so on. And you also can create many interesting inter...

DF-FIT0180

This type of photoresistor is made of environment-friendly materials(no Cadmium and Lead) compared with the traditional CDS photoresistor.

SF-DEV-09281

The WiiChuck Adapter is a small PCB that is designed to be inserted into the connector of a Nintendo Wii Nunchuck to provide access to all 4 wires of the remote. The power, ground and two-wire interface of the Nunchuck are all broken out to a 4-pin 0.1" pitch header.

LB-LR0205

Feeling tipsy?  

AF-2056

This is really the fanciest, best feeling knob we've ever seen. Using this knob sort of reminded us of driving along the Amalfi coast in a perfectly restored '65 Porsche - meaning we really, really liked it.  We hand selected the best knobs for your project in different sizes ...

FT-AM3X

Which way is up?

FT-HALL

 Sense magnetic presence, rotating wheels and magnets, door and arm sensors, and anything else magnetic nearby this sensor.

DF-DFR0430

INTRODUCTION

FT-LIGHT

Does the fridge light really turn off? Now you can find out!

FT-TEMP

Sprinkle these around your house to collect temperature data using your Arduino. This DS18B20-based 1-wire bus temperature sensor module is easy to connect and use, and you can even daisy-chain several together on the same wire. 0.5°C accuracy and fast response.

DF-SEN0171

This is a PIR(passive infrared motion) sensor designed to work with Arduino and Raspberry Pi. It allows you to sense motion, it is commonly used to detect whether a human has moved in or out of the sensors range. They are small, inexpensive, low-power, easy to use and don't we...