Sensors

It's a push button!

Use this module to detect a magnetic field.  This is an Analog sensor, when a magnet is detected the LED will turn on, otherwise the LED will be off.

With the sound module, we can detect the presence of loud sounds. While this module has a microphone on it, our Arduino does not have the brains to interpret or record the audio directly (there are some shields you can get that will do this).

Arduino to SD card interface module.Use this to read and write to the SD card using your arduino.

Do you love your plants? Do you want the best for them? Or are you more like me and forget they are there until your mother is about to come over then rush round the house making sure they have been watered? Either way this kit is for you!

45 sensors for Arduino

When wired with a 5v supply, the power light will be on.

CdS cells are little light sensors. As the squiggly face is exposed to more light, the resistance goes down. When its light, the resistance is about 5-10KΩ, when dark it goes up to 200KΩ.

We designed this board to give the user a very discrete button without any sharp edges. Button closes when you push it and opens when you release (momentary push button).

The Prop Shield with Motion Sensors for Teensy 3.2 and Teensy-LC is meant for making interactive light and sound effects on small handheld props and wearable costumes! Good for all sorts of projects, and designed by the creator of the Teensy so you know it's gonna be well supp...

This is a very small light sensor. A photocell changes (also called a photodetector, photo resistor, CdS or photoconductive cell) resistance depending on the amount of light it is exposed to. These little sensors make great ambient light triggers (when light in the room turns ...

This is a touch sensor for Arduino.   This sensor is a toggle output type: touch-on then touch-off.

This stand alone DHT11 can read the temperature and humidity and send the information over a one wire, simplex serial bus. Arduino.cc provides a DHT11 library to aid in communicating with this module.

The MPU-6050 sensor contains a MEMS accelerometer and a MEMS gyro in a single chip. It is very accurate, since it contains 16-bits analog to digital conversion hardware for each channel. Therefor it captures the x, y, and z channel at the same time.

Wide range, low power temperature sensor outputs an analog voltage that is proportional to the ambient temperature. To use, connect pin 1 (left) to power (between 2.7 and 5.5V), pin 3 (right) to ground, and pin 2 to analog in on your microcontroller. The voltage out is 0V at -...

This is a simple, thumbnail-size RFID tag. These tags are great for sensing presence, identification, etc., and they’re small, so they can be easily sewn into clothing or inserted into enclosures. Each tag comes with a unique 32-bit ID code and is not reprogrammable. The carri...

This white LED light module has a shiny white color. It is ideal for Arduino starter. This module can be easy to be plugged on IO/Sensor expansion shield.

A miniature snap-action switch, also trademarked and frequently known as a micro switch, is an electric switch that is actuated by very little physical force.Micro switches are very widely used; among their applications are appliances, machinery, industrial controls, vehicles,...

A simple flex sensor 2.2" in length. As the sensor is flexed, the resistance across the sensor increases. Patented technology by Spectra Symbol - they claim these sensors were used in the original Nintendo Power Glove. I love the Nintendo Power Glove. It’s so bad!

A soil moisture sensor can read the amount of moisture present in the soil surrounding it. It's an ideal for monitoring an urban garden, or your pet plant's water level. This is a must have component for a IOT garden / Agriculture!

10K thermistor with a negative temperature coefficient. Good choice for temp-sensing applications when you need a reliable NTC thermistor.

The RHT03 (also known by DHT-22) is a low cost humidity and temperature sensor with a single wire digital interface. The sensor is calibrated and doesn’t require extra components so you can get right to measuring relative humidity and temperature.

These simple switches are the Mechanical Bumper sensor for the SparkFun RedBot, giving you the ability to detect a collision before it really happens. This sensor works by acting as a SPST switch. When the “whisker” bumps into a foreign object it will make contact with a nut n...

This small form factor micro servo with 360 degree continuous rotation is compatible with servo shields for Arduino. It's a very versatile small servo motor for micro robots or other applications where you don't have much space and the need of a full rotational motor with the ...

The DS1307 Real Time Clock module developed by one of our designers: Waiman. The module comes fully assembled and pre-programmed with the current time (ok, so it's our current time - MST). The included Lithium coin cell battery (CR1225 41mAh) will run the module for a minimu...

RFID (radio-frequency identification) is the wireless non-contact use of radio-frequency electromagnetic fields, for the purposes of identifying and tracking tags attached to objects. This is the ID-12LA, a very simple to use RFID reader module from ID Innovations. With a buil...