Raspberry Pi Pi HATs & Plates

LB-LS0657

The HIFI DAC expansion board designed for the Raspberry Pi. The user can use this expansion board with audio playback systems to build its own network HIFI player. The expansion board provides two kinds of output interfaces to facilitate external amplifiers and other equipm...

FT-PIBR

Need to attach some electronic components or sensors to your Raspberry Pi? PiBreak is a prototyping board for the Raspberry Pi. It provides labelled breakout pins for all GPIOs, a large prototyping area with solder pads, and power rails for easy power connection.

AF-2738

Control the same hardware as used in space...build your very own Astro Pi with the new Raspberry Pi Sense HAT! The Raspberry Pi Sense HAT is attached on top of the Raspberry Pi via the 40 GPIO pins to create an ‘Astro Pi’. The Sense HAT has several integrated circuit based sen...

FT-PISC

Easily connect the 128x128 Pixel OLED Module to your Raspberry Pi using this handy expansion board.

AF-2340

This touch-able add on HAT for Raspberry Pi will inspire your next interactive project with 12 capacitive touch sensors. Capacitive touch sensing works by detecting when a person (or animal) has touched one of the sensor electrodes. Capacitive touch sensing used for stuff like...

DF-DFR0357

The Expansion Shield X200 is a most cost-effective shield which could apply to Raspberry Pi Model B+, Raspberry Pi 2 Model B and newest Raaspberry Pi 3 Model B. It integrates a lot of very useful functions such as RTC real time clock; audio input and output; VGA output; USB hu...

AF-2714

Stack and connect multiple plates and breakout PCB's onto your Raspberry Pi with this custom-made, 2x20 extra tall SMT female header. 

DF-DFR0450

INTRODUCTION

AF-2310

Design your own Pi HAT, attach custom circuitry and otherwise dress your Pi A+, B+, or Pi 2 with this jaunty prototyping HAT kit.

AF-2454

A TFT panel connected to a Raspberry Pi without the use of an HDMI decoder? What is this sorcery??? It's the DPI Kippah from Adafruit! This HAT-like* board snaps onto a Raspberry Pi B+, A+, Pi 2, Pi 3 or Zero and with a little software configuration, allows you to have what no...

FT-PIBP

Need to attach some electronic components or sensors to your Raspberry Pi? PiBreak Plus is a prototyping board for the Raspberry Pi. It provides labelled breakout pins for all GPIOs, a large prototyping area with solder pads, and power rails for easy power connection.

AF-2314

Design your own Pi HAT, attach custom circuitry and otherwise dress your Pi A+, B+, or Pi 2 with this jaunty prototyping HAT kit with EEPROM

AF-3402

Pimoroni has taken all the great features of the Picade PCB and crammed them onto this super Picade HAT. It's the best, easiest way to make a super-sweet arcade system using any Raspberry Pi.

DF-DFR0358

This Raspberry Pi is Discontinued Now, We recommend other raspberry pi shields as a suitable replacement.

AF-3473

What if Scroll pHAT had twice times as many pixels and individual pixel brightness control? Scroll pHAT HD, that's what!!

AF-2327

The Raspberry Pi is a wonderful little computer, but one thing it isn't very good at is controlling DC Servo Motors - these motors need very specific and repetitive timing pulses to set the position. Instead of asking the Pi Linux kernel to send these signals, pop on this hand...

AF-3335

PaPiRus Zero is an ePaper / eInk screen pHAT designed for the Raspberry Pi Zero. It’s one of the first true low power displays for the Pi Zero mini computer.

AF-1940

The RaspiRobot Board v3 is an expansion board designed to turn your Raspberry Pi into a motor controller! This board comes fully assembled and includes a switched-mode power supply so you can supply your Raspberry Pi from a variety of battery packs.

AF-4121

You won't be able to look away from the mesmerizing patterns created by this Adafruit CharliePlex LED Matrix Display Bonnet. This 16x8 LED display can be placed atop any Raspberry Pi computer with a 2x20 connector, for a beautiful, bright grid of 128 charlieplexed LEDs. It ev...

AF-4119

You won't be able to look away from the mesmerizing patterns created by this Adafruit CharliePlex LED Matrix Display Bonnet. This 16x8 LED display can be placed atop any Raspberry Pi computer with a 2x20 connector, for a beautiful, bright grid of 128 charlieplexed LEDs. It ev...

AF-3224

Add precise capacitive touch, distance sensing and high quality audio to your Raspberry Pi A+, B+, Zero and later (any Raspberry Pi with a 40 pin GPIO connector) with the Pi Cap from Bare Conductive! Connect Electric Paint or anything conductive to one of the 12 electrodes to ...

AF-3935

Pimoroni's GFX HAT is a shiny new LCD Display with RGB Backlight and Touch Buttons! This is a seriously snazzy LCD that can display complex graphics for all your headless Pi games and animations. While the LCD is monochrome 128x64 pixels, the backlight can be set to different ...

DF-DFR0449

INTRODUCTION

AF-2336

"These go to eleven."  11 millimeters that is!

AF-1687

The RTK Raspberry Pi Motor Controller Board Kit is a simple to use, budget-friendly, motor controller board for the Raspberry Pi that allows you to control motors using the GPIO Pins with very little coding.

FT-PILV

The PiLeven is an Arduino Uno compatible board that fits directly onto a Raspberry Pi, giving you the best of both worlds. You can run a full operating system on the Pi with whatever high-level management software you like, while using the PiLeven for I/O using its Arduino R3 ...

AF-2288

Snap the Pimoroni Unicorn Hat on top of a Raspberry Pi model A+ or a model B+ for a fun 8x8 RGB LED matrix powered directly from the Pi.

AF-3464

Pocket-sized fun is the name of this game, with the Joy Bonnet – our most fun Bonnet ever (no we didn't even think that was possible, either!). This Bonnet fits perfectly on top of your Raspberry Pi Zero (any kind) and gives you adorable hand-held arcade controls. Once you ins...

AF-3422

Playing retro games is easy on a Raspberry Pi - and that pocket-sized computer is pretty good at it too! All you need is a little help to connect buttons and a joystick up and you can custom design your own arcade console, desktop or stand-up machine, even just a simple contro...

AF-2187

For super-slim SMT designs, this custom-made, 2x20 short SMT female header can be used to plug a Raspberry Pi HAT onto a B+ or A+ or Pi 2. It's harder to use than the Thru-Hole type headers, but for the slickest, slimmest fit, this header is recommended!