Cosplay/costuming

PL-1817

0.1" connector custom cable.

AF-1170

These magnetic pin backs have two pieces: a metal bar with adhesive strip and a plastic piece with two strong rare-earth magnets.

AF-870

What's better than a single LED? Lots of LEDs! A fun way to make a small display is to use an 8x8 matrix or a 4-digit 7-segment display.

AF-182

This sensor can detect flexing or bending in one direction. They were popularized by being used in the Nintendo PowerGlove as a gaming interface.

AF-166

FSRs are sensors that allow you to detect physical pressure, squeezing and weight. They are simple to use and low cost. This sensor is a Interlink model 402 FSR with 1/2 diameter sensing region.

AF-406

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC signal is applied to it, it glows an aqua (blue green) color. You can make it look different colors by changing the coating, for e...

SF-COM-11154

This is a standard 3.5mm stereo jack with no frills. Panel mount in a 6mm diameter hole for a nice clean headphone, microphone or serial data connection.

AF-1247

Add motion and direction sensing to your wearable FLORA project with this high precision 3-axis Accelerometer+Compass sensor.

AF-1244

This woven conductive ribbon is great for powering lots of LEDs in a wearable project.

AF-301

Need some really bright LEDs? We are big fans of these clear blue LEDs, in fact we use them exclusively in our kits. They are very bright and have about 20degree LED beam. They go easily into a breadboard and will add that extra zing to your project.

AF-1405

Get started with the fabulous Adafruit Flora platform with this lovely budget kit, just enough to get you started with this fun wearable computer.

PL-1802

0.1" connector custom cable.

AF-415

EL tape is the big sister to EL wire - it has the same glow effect but with a flat, wide shape instead of a round shape. The glowing part of the tape is 1 cm wide (the plastic coating is about 1.5cm wide). The other side has an adhesive on it so you can stick the tape onto som...

AF-416

EL tape is the big sister to EL wire - it has the same glow effect but with a flat, wide shape instead of a round shape. The glowing part of the tape is 1 cm wide (the plastic coating is about 1.5cm wide). The other side has an adhesive on it so you can stick the tape onto som...

AF-1356

Your electronics can now see in dazzling color with this lovely color light sensor.

AF-1894

Finally, the conductive material you've known you wanted but never knew you could have, its a sheet of flex PCB material! This is the stuff used to make flexible circuits, but raw and unetched. You can treat it just like 1 oz copper clad, etch it with ferric chloride (or other...

AF-1317

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful.

PL-1880

0.1" connector custom cable.

SF-PRT-12639

This is a 3.5mm TRRS SMD audio jack. TRRS connectors are the audio-style connectors that you see on some phones, MP3 players and development boards. TRRS stands for “tip, ring, ring, sleeve,” which reflects the fact that, unlike a standard stereo connector, this actually has t...

AF-1781

Need a big battery for your project? This lithium ion battery contains a 2200mAh and a protection circuit that provides over-voltage, under-voltage and over-current protection. Yet, it is slim and easy to fit into many project cases.

AF-640

After months of searching, we finally have what we consider to be the ultimate conductive thread.

AF-896

Add sparkle to your project with these lovely silver wire LED strands.

PL-2634

We carry stranded hook-up wire in an assortment of gauges and colors:

PL-1807

0.1" connector custom cable.

PL-1810

0.1" connector custom cable.

PL-1831

0.1" connector custom cable.

AF-1070

This sensor can detect flexing or bending in one direction. They were popularized by being used in the Nintendo PowerGlove as a gaming interface.

AF-1063

Add an ear to your project with this well-designed electret microphone amplifier.

PL-1844

0.1" connector custom cable.

SF-DEV-14034

The Spectacle Audio Board allows you to add sound from a microSD card to your Spectacle projects. Each board accepts a microSD card with sounds in .ogg format, and has a 1/8" (3.5mm) audio jack line-level output ready to be amplified. It is important to know that the files use...