Cosplay/costuming

AF-50

We sure love the ATmega328 here at Adafruit, and we use them a lot for our own projects.

MD-20008

A group kit of cardboard construction makedo tools for many hands to make light work.

AF-653

This battery holder is by far the easiest way to add a battery to a small wearable project. By coincidence, there are two small 1mm diameter holes in the metal connection tabs, just large enough for a #5 or smaller needle to pass through. One tab connects to common ground (neg...

AF-1756

Sew a little sparkle into your wearable project with an Adafruit LED Sequin. These are the kid-sister to our popular Flora NeoPixel, they only show a single color and they don't have digital control, but that makes them smaller easier to use for many projects.

AF-659

FLORA is Adafruit's fully-featured wearable electronics platform. It's a round, sewable, Arduino-compatible microcontroller designed to empower amazing wearables projects.FLORA comes with Adafruit's support, tutorials and projects. Check out dozens of FLORA tutorials on the Ad...

AF-1463

Round and round and round they go! 16 ultra bright smart LED NeoPixels are arranged in a circle with 1.75" (44.5mm) outer diameter. The rings are 'chainable' - connect the output pin of one to the input pin of another. Use only one microcontroller pin to control as many as you...

AF-615

Mighty needles, sew like the wind! This needle set is the only one you'll need for any sort of hand sewing, especially using our conductive thread and wearable electronics parts.

AF-1755

Sew a little sparkle into your wearable project with an Adafruit LED Sequin. These are the kid-sister to our popular Flora NeoPixel, they only show a single color and they don't have digital control, but that makes them smaller easier to use for many projects.Simply connect 3 ...

AF-3377

Sew a little sparkle into your wearable project with an Adafruit LED Sequin. These are the kid-sister to our popular Flora NeoPixel, they only show a single color and they don't have digital control, but that makes them smaller easier to use for many projects.

AF-1222

Love FLORA but want a bite-sized version? Look no further, GEMMA is a tiny wearable platform board with a lot of might in a 1" diameter package. Powered by a Attiny85 and programmable with an Arduino IDE over USB, you'll be able to realize any wearable project!

$10.24
AF-169

Tiny little servo can rotate approximately 180 degrees (90 in each direction), and works just like the standard kinds you're used to but smaller. You can use any servo code, hardware or library to control these servos. Good for beginners who want to make stuff move without bui...

AF-1792

Sew a little sparkle into your wearable project with an Adafruit LED Sequin. These are the kid-sister to our popular Flora NeoPixel, they only show a single color and they don't have digital control, but that makes them smaller easier to use for many projects.

AF-1757

Sew a little sparkle into your wearable project with an Adafruit LED Sequin. These are the kid-sister to our popular Flora NeoPixel, they only show a single color and they don't have digital control, but that makes them smaller easier to use for many projects.Simply connect 3 ...

PL-1801

0.1" connector custom cable.

AF-564

A small, portable inverter for EL wire. Powers off of 4 AAA batteries (not included!), it can drive 3-4 meters (10 to 13 feet) of our high-brightness EL wire OR 1 meter (3 feet) of EL tape OR a 10cmx10cm piece of EL panel for about 7 hours.

AF-1260

What's a wearable project without LEDs? Our favorite part of the Flora platform is these tiny smart pixels.

AF-1685

Push once to turn one side on, push again to turn the other side on! It's basically a push-button toggle switch that connects and disconnects the middle pin from either of the two side switches with every click.This clicky switch makes a great power switch or mode toggler. We ...

AF-1246

Add light-reactive sensing to your wearable Flora project with this high precision Lux sensor.

PL-1804

0.1" connector custom cable.

AF-354

Need a big battery for your project? This lithium ion pack is made of 2 balanced 2200mAh cells for a total of 4400mA capacity! The cells are connected in parallel and spot-welded to a protection circuit that provides over-voltage, under-voltage and over-current protection.

AF-1758

Sew a little sparkle into your wearable project with an Adafruit LED Sequin. These are the kid-sister to our popular Flora NeoPixel, they only show a single color and they don't have digital control, but that makes them smaller easier to use for many projects.

SF-PRT-10588

Simple breakout board for the 3.5mm audio jack. Use this breakout (shipped bare) to allow breadboard or SIP access to the super-common 3.5mm audio jack. All five pins are broken out.

AF-128

This is our most popular XBee wireless module: the series 1 802.15.4 protocol 1mW with wire antenna. Its good for point-to-point, multipoint and convertible to a mesh network point. We suggest this module for those starting out as it is the easiest to get going: if there are t...

PL-2640

We carry stranded hook-up wire in an assortment of gauges and colors:

AF-1405

Get started with the fabulous Adafruit Flora platform with this lovely budget kit, just enough to get you started with this fun wearable computer.

AF-1324

Conductive hook & loop tape is just like the stuff you've seen on jackets, clothes, shoes, and bags, but is coated with silver to make it fully conductive.

AF-1131

By popular demand, we now have a handy extension cord for all of our JST-terminated battery packs (such as our LiIon/LiPoly and 3xAAA holders).

$1.39
SF-PRT-08631

Simple RCA jack. Can be used on any project requiring RCA Audio, Video, or simple analog transmission.

PL-1817

0.1" connector custom cable.

SF-COM-11154

This is a standard 3.5mm stereo jack with no frills. Panel mount in a 6mm diameter hole for a nice clean headphone, microphone or serial data connection.