Battery Holders

DF-FIT0110

This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive male barrel jack. If you need to connect bare wires to a barrel jack on an Arduino or a development board, this might be the sim...

AF-1867

Simple but effective - this breakout board has a CR1220 coin cell battery holder soldered on, an on/off switch and 0.1" pitch breakout pins for easy connecting. Great for powering very low-current projects, or adding a battery backup circuit to a real-time-clock or similar. Th...

AF-1871

Simple but effective - this sewable breakout board has a CR2032 coin cell battery holder soldered on, an on/off switch and 0.1" pitch breakout pins for easy connecting. Great for powering very low-current projects, or adding a battery backup circuit to a real-time-clock or sim...

AF-653

This battery holder is by far the easiest way to add a battery to a small wearable project. By coincidence, there are two small 1mm diameter holes in the metal connection tabs, just large enough for a #5 or smaller needle to pass through. One tab connects to common ground (neg...

DF-FIT0151

This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm(0.22x0.08"), center-positive female barrel jack. If you have a power supply with a barrel jack and want to plug it into a breadboard, this might ...

DF-FIT0141

This battery holder can hold 6 AA battery which is able to become a 7.2 V rechargeable battery pack from NiMH / NiCd cells or 9V battery pack from alkaline cells.

AF-80

I found these high-quality battery clips. They're molded plastic so they wont tear like cheap clips, and they cover the battery terminals to prevent shorts.

DF-FIT0079

Simple 4 Cell AA Battery holder with 5" tinned leads, square configuration.

DF-FIT0131

This simple cable has so many uses! Plug a 9V battery into one end and connect the other end to anything with a 5.5x2.1mm, center-positive barrel jack.

DF-FIT0266

This battery holder can hold 6 AA battery which can make 7.2 V rechargeable battery pack from NiMH / NiCd cells or 9V battery pack from alkaline cells.

DF-FIT0398

A Difficult Choice Made Easy

AF-783

This tiny coin cell battery holder is ideal for small portable or wearable projects.

AF-1862

A simple 2-pin connector soldered onto a breadboard-friendly breakout. This is compatible with the "JST PH 2-pin" connector. Mates perfectly with all our 1-cell LiPoly and LiIon batteries as well as our 6V coin cell holder and 3xAAA battery pack. We also have simple JST pigtai...

AF-1863

This switched JST connector is the best way to quickly prototype with our LiPoly batteries. We paired a genuine JST connector with a slide switch that can do up to 600mA. Both are soldered onto a breadboard-friendly breakout. There's two ground pins, one 'switched' power pin, ...

DF-FIT0080

INTRODUCTION

AF-1868

Simple but effective - this breakout board has a CR1220 coin cell battery holder soldered on and 0.1" pitch breakout pins for easy connecting. Great for powering very low-current projects, or adding a battery backup circuit to a real-time-clock or similar.Comes with one fully ...

DF-FIT0043

This is the second version of the 9V to Barrel Jack Adapter. In this version the material for the 9V battery jack is hard plastic, which makes it easier to connect and disconnect

DF-FIT0078

This battery holder can hold 6 AA battery which can make 7.2 V rechargeable battery pack from NiMH / NiCd cells or 9V battery pack from alkaline cells.

DF-DFR0303

Small and exquisite, this USB power detector displays charging voltage and current at same time in one screen. Checking power consumption of arduino and various modules cannot be more easier with this detector.

DF-FIT0337

This small capsule is a 4.5V button cell battery holder for mini power solutions.Its minimalism design in clean white cylinder body and matte surface makes it an elegant power capsule in your projects. It also includes 3* LR44 cell battery to make sure that you can start right...

DF-DFR0368

Reliable, self-sustainable power to individuals anywhere, anytime.

AF-875

Make a portable power brick with plenty of juice! Use Alkaline AA's for a 12V 3000-4000mAh power supply, or rechargeable NiMH for 2000mAh 9.

AF-771

Keep your power source safe and toasty in these waterproof 3xAA battery holders.

AF-830

Make a nice portable power pack with this 4 x AA battery holder.

DF-FIT0163

This is a 5V USB charger wall wart. Ideal for supplying power to your Arduino when there is no computer near by. It can be used as Arduino power or chager for any USB device such as Mobile Phones, Iphone, Ipad and Tablet.

AF-2271

This is an interesting kind of battery holder, usually you'll see ones that are designed for holding like AAA's or something. This battery holder is designed to clip into and hold camcorder batteries. Specifically, the common Canon LP-E6 rechargeable Lithium-Ion Battery Pack (...

AF-4191

This battery holder connects 2 AAA batteries together in series for powering all kinds of projects. We spec'd these out because the box is nicely slim, and 2 AAA's add up to about 3V for low-voltage electronics projects, plus it has a nifty on-off switch.

AF-4193

This battery holder connects 2 AA batteries together in series for powering all kinds of projects. We spec'd these out because the box is fairly slim, and 2 AA's add up to about 3V for many low voltage electronics projects, plus it has a nifty on-off switch.

AF-4194

This battery holder connects 2 AA batteries together in series for powering all kinds of projects. We spec'd these out because the box is fairly slim, and 2 AA's add up to about 3V for many low voltage electronics projects, plus it has a nifty on-off switch.

SF-PRT-15101

This is a unique two-cell AAA battery holder built specifically for the BBC micro:bit. The 6" (~150mm) cable has been terminated with a JST-PH connector.