Wireless Antennas

SF-WRL-09232

This is an adapter that converts an RP-SMA board to an SMA antenna. The adapter will connect to any of our 2.4GHz wireless boards (Bluetooth, Nordic, or XBee) or interface cables and will allow you to use an antenna/cable with an SMA connection.

SF-WRL-00662

This connector cable interfaces UFL RF connectors to RP-SMA antennas. Use it to attach any standard RP-SMA 2.4GHz antenna to the our WiFly Shield.

SF-WRL-00558

Need range? 2.4GHz Large Duck Antenna 5dBi with Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm impedance.

AF-3237

That's one slim cellular antenna! At 238mm long from tip to tip and and with a cable thickness of just 2mm, this 3dBi GSM antenna is slim, compact and sensitive, with a 3dBi gain. The antenna juts out from its base with stick-on back so you attach it to an enclosure if you're ...

AF-1991

That's one slim cellular antenna! At just 75mm long from tip to tip and and with a thickness of just 2mm, this 3dBi GSM antenna is slim, compact and sensitive, with a 3dBi gain.  The antenna juts out from its base with stick-on back so you attach it to an enclosure if you're m...

SF-WRL-00145

2.4GHz Duck Antenna 2.2dBi with Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm impedance. 4" long.

AF-944

This 4"/100mm long swivel dipole antenna has 2dBi of gain and 50Ω impedance so it will work fantastically with just about any 2.4-2.5GHz wireless receiver/transmitter such as:

SF-WRL-14131

This is your solution when you absolutely, positively need to get the most out of an antenna for your next RFID project. This ultra high-frequency (UHF) RFID Antenna boasts a frequency range of 860-960 MHz with a gain of 6dBi. This is the same external antenna we use for our S...

SF-WRL-00144

2.4GHz ceramic chip antennas. Very small antennas that work nicely with the Nordic ICs. Don’t expect these little guys to perform as well as their ~2" rubber duck counter parts, but then again, these will squeeze onto any PCB layout.

SF-WRL-13982

This ANT700 is a telescopic antenna designed for operation from 300 MHz to 1.1 GHz with a total length that is configurable from 9.5 cm to 24.5 cm. Each ANT700 is constructed of stainless steel and features an SMA male connector, rotating shaft, and adjustable elbow.

AF-1858

This 2.2"/57mm long antenna has 2dBi of gain and 50Ω impedance so it will work fantastically with just about any 850/900/1800/1900/2100 wireless receiver/transmitter such as any Cellular or GSM/GPRS device.

SF-WRL-00593

PCB edge mount - SMA RF connector. Perfect for prototyping with the GPS and Cellular devices that require an antenna connection. These connectors have a female signal pin and will correctly mate with the original SMA type antennas.

AF-960

Give your Ultimate GPS V3 a boost with this external active antenna.

AF-2461

Wow that's a tiny GPS antenna! This passive antenna is only 15mm x 15mm x 6.8mm in size, with a 50mm long uFL cable. Great for when you want to keep things small.

AF-945

This 8"/200mm long swivel dipole antenna has 5dBi of gain and 50Ω impedance so it will work fantastically with just about any 2.4-2.5GHz wireless receiver/transmitter such as:

SF-WRL-11320

This adhesive, omni-directional antenna is perfect for situations when you’re trying to get a signal out from a transmitter that you’ve jammed down into an enclosure. Operating on the 2.4GHz band, it works great for WiFi, Bluetooth or ZigBee. Just connect the antenna using the...

AF-3584

ANT500 from Great Scott Gadgets is a telescopic antenna designed for operation from 75 MHz to 1 GHz. Its total length is configurable from 20 cm to 88 cm. ANT500 is constructed of stainless steel and features an SMA male connector, rotating shaft, and adjustable elbow.

AF-3585

ANT700 from Great Scott Gadgets is a lightweight telescopic antenna designed for operation from 300 MHz to 1100 MHz. Its total length is configurable from 9.5 cm to 24.5 cm. ANT700 is constructed of stainless steel and features an SMA male connector, rotating shaft, and adjust...

SF-GPS-15004

Want to improve your GPS antenna multipath convergence time performance to near survey-grade GNSS levels? Just using this simple steel plate effectively improves simple patch antenna performance to near professional level antenna setups.

SF-GPS-15246

The Molex GNSS Flex antenna is a great option for basic GNSS applications and will work with any of our GNSS boards equipped with a U.FL at a fraction of the cost of many of its big brothers. This antenna supports GPS, Galileo, BeiDou, and GLONASS in three different frequency ...

SF-GPS-15247

What is the best chip antenna for your GNSS project? There are tons to choose from, but finding the right one might be tricky so here's a board that helps make deciding easier. The SparkFun GNSS Chip Antenna Evaluation Board makes it easy to test out various sized GPS antennas...

SF-CEL-15054

This high-gain duck antenna is designed for LTE devices that operate in the 690-960MHz and 1710-2690 MHz bands.

SF-WRL-13002

This ANT500 is a telescopic antenna designed for operation from 75 MHz to 1 GHz with a total length that is configurable from 20 cm to 88 cm long. Each ANT500 is constructed of stainless steel and features an SMA male connector, rotating shaft, and adjustable elbow.

AF-3623

This antenna is a perfect addition to your cellular project with LTE connectivity. It's specifically intended for use with the Pycom LTE-powered kits but it's just a passive antenna so you can pair it with any dev board you like, as long as it has a uFL connector.

SF-WRL-09143

900/1800 MHz Duck Antenna 2dBi with regular RP-SMA RF connector. Perfect for use with the XBee 900MHz units. 50 ohm impedance. 105mm long.

SF-WRL-09144

Itty-bitty U.FL SMD connector. Great for tight PCB layouts that require antenna connections.

AF-3340

This LoRa Antenna Kit is meant for use with the LoPy LoRa, WiFi and BLE board or the SiPy Sigfox, WiFi and BLE board. But, it's good for any 900MHz radio, including our LoRa breakouts/Feathers or even the RFM69 900MHz radios we stock!

SF-WRL-15126

After years of popularity with the XBee Series 1 and XBee Series 2, we now have the XBee Series 3 which brings the best of both worlds. XBee 3 not only handles 802.15.4, and ZigBee, but also BLE protocols and you can now talk to the modules over UART or SPI as well. With a 200...

SF-GPS-15192

The ANN-MB-00 GNSS multiband antenna is extremely unique from other GNSS/GPS antennas in that it is designed to receive both the classic L1 GPS band and the newly launched (started in 2005) L2 GPS band. Additionally, the ANN-MB-00 from u-blox is extremely well built with both ...

SF-WRL-00592

PCB edge mount Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. This is a standard edge connector. The thickness between pins is 0.063" so that it can slide sideways onto a PCB. See the mechanical drawing to create your footprint.